another a10 uart

My cheap android set top box finally stopped booting - it's already had a couple of episodes where it's needed factory defaulting but this time it was just getting stuck on the first boot screen. The accessible system information - from when it used to boot - had already confirmed my suspicion that it was another A10 device and so I thought it was time to crack it open and see if I could find the uarts again.
I was expecting to have to probe out a bunch of anonymous pads again but instead the pins were clearly marked:

Above you can easily see the rx, tx pads, along with 3.3v and what I'm guessing is a bunch of SPI (MS, CK, DI, DO, DO1 DO2) pins. Although I didn't have to spend any time looking for the uart, due to their tiny size they were difficult to solder - I managed to lift both the pads from the board and ended up having to solder the wires (which are far too heavy at this scale) to the edge of the resistors that are on the lines - next time I do this I'm using an air station. The tx and rx were hooked up to an FTDI board via a couple of level shifters. Here's the output from the initial boot:
HELLO! BOOT0 is starting!
boot0 version : 1.5.0
dram size =1024
Succeed in opening nand flash.
Succeed in reading Boot1 file head.
The size of Boot1 is 0x00074000.
The file stored in 0X00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[ 0.212] boot1 version : 1.6.0
[ 0.212] pmu type = 3
[ 0.213] bat vol = 0
[ 0.217] set dcdc2 failed, set default clock 384M
[ 0.219] script installed early
[ 0.222] script_main_key_count=81
[ 0.226] key
[ 0.239] no key found
[ 0.239] flash init start
[ 0.239] NB1 : enter NFB_Init
[ 0.242] NB1 : enter phy init
[ 0.245] [NAND] nand driver version: 0x0x00000002, 0x0x00000011, data: 0x20120926
[ 0.253] [NAND] nand driver: secure debug v1.2.9, 20121103, 13:09
[ 0.259] NAND_RequestDMA ok
[ 0.262] NFC Randomizer start.
[ 0.266] [SCAN_DBG] Nand flash chip id is:0x0x0000002c 0x0x00000068 0x0x00000004 0x0x426ffdfc 0x0x42428638 0x0x424529d0
[ 0.277] Nand Unique ID of chip 0 is :
[ 0.281] 0x000000ea, 0x000000bc, 0x0000004e, 0x426ffd84
[ 0.287] 0x00000010, 0x000000f8, 0x00000020, 0x426ffd84
[ 0.292] 0x000000ff, 0x00000000, 0x000000ff, 0x426ffd84
[ 0.298] 0x000000ff, 0x00000000, 0x000000ff, 0x426ffd84
[ 0.303]
[ 0.305] 0x00000015, 0x00000043, 0x000000b1, 0x426ffd84
[ 0.310] 0x000000ef, 0x00000007, 0x000000df, 0x426ffd84
[ 0.316] 0x00000000, 0x000000ff, 0x00000000, 0x426ffd84
[ 0.321] 0x00000000, 0x000000ff, 0x00000000, 0x426ffd84
[ 0.327]
[ 0.329]
[ 0.330] [SCAN_DBG] ==============Nand Architecture Parameter==============
[ 0.338] [SCAN_DBG] Nand Chip ID: 0x0x4a04682c 0x0xffffffff
[ 0.345] [SCAN_DBG] Nand Chip Count: 0x0x00000001
[ 0.350] [SCAN_DBG] Nand Chip Connect: 0x0x00000001
[ 0.356] [SCAN_DBG] Nand Rb Connect Mode: 0x0x00000001
[ 0.362] [SCAN_DBG] Sector Count Of Page: 0x0x00000008
[ 0.368] [SCAN_DBG] Page Count Of Block: 0x0x00000100
[ 0.374] [SCAN_DBG] Block Count Of Die: 0x0x00001000
[ 0.379] [SCAN_DBG] Plane Count Of Die: 0x0x00000002
[ 0.385] [SCAN_DBG] Die Count Of Chip: 0x0x00000001
[ 0.391] [SCAN_DBG] Bank Count Of Chip: 0x0x00000001
[ 0.396] [SCAN_DBG] Optional Operation: 0x0x00001208
[ 0.402] [SCAN_DBG] Access Frequence: 0x0x00000028
[ 0.408] [SCAN_DBG] ECC Mode: 0x0x00000002
[ 0.414] [SCAN_DBG] Read Retry Type: 0x0x00000000
[ 0.419] [SCAN_DBG] DDR Type: 0x0x00000000
[ 0.425] [SCAN_DBG] =======================================================
[ 0.433] [SCAN_DBG] ==============Optional Operaion Parameter==============
[ 0.440] [SCAN_DBG] MultiPlaneReadCmd: 0x0x00000000, 0x0x00000030
[ 0.447] [SCAN_DBG] MultiPlaneWriteCmd: 0x0x00000011, 0x0x00000080
[ 0.454] [SCAN_DBG] MultiPlaneCopyReadCmd: 0x0x00000000, 0x0x00000000, 0x0x00000035
[ 0.462] [SCAN_DBG] MultiPlaneCopyWriteCmd: 0x0x00000085, 0x0x00000011, 0x0x00000080
[ 0.471] [SCAN_DBG] MultiPlaneStatusCmd: 0x0x00000070
[ 0.477] [SCAN_DBG] InterBnk0StatusCmd: 0x0x00000078
[ 0.482] [SCAN_DBG] InterBnk1StatusCmd: 0x0x00000078
[ 0.488] [SCAN_DBG] BadBlockFlagPosition: 0x0x00000001
[ 0.494] [SCAN_DBG] MultiPlaneBlockOffset: 0x0x00000001
[ 0.500] [SCAN_DBG] =======================================================
[ 0.507] NB1 : nand phy init ok
[ 0.511] Request memory for lsb page table
[ 0.515] page type: 0x00000000
[ 0.519] Init lsb page table ok
[ 1.728] _RepairLogBlkTbl start
[ 1.728] [DUBG], check free block 0x000007fe ok!
[ 1.870] Log Block Index 0x00000000, LogicBlockNum: 0x000001e1, LogBlockType: 0x00000001
[ 1.872] log0: 0x00000702, Log1: 0x000007fe, WriteIndex: 0x00000000
[ 1.879] datablock: 0x0000068e, lastusedpage: 0x0000000e
[ 1.885] [DUBG], check free block 0x000007fa ok!
[ 2.029] Log Block Index 0x00000001, LogicBlockNum: 0x000001e3, LogBlockType: 0x00000001
[ 2.032] log0: 0x0000070c, Log1: 0x000007fa, WriteIndex: 0x00000000
[ 2.039] datablock: 0x000005f9, lastusedpage: 0x00000007
[ 2.184] Log Block Index 0x00000002, LogicBlockNum: 0x000001e0, LogBlockType: 0x00000001
[ 2.187] log0: 0x0000071c, Log1: 0x000007f8, WriteIndex: 0x00000001
[ 2.194] datablock: 0x0000065b, lastusedpage: 0x0000000a
[ 2.200] [DUBG], check free block 0x000007f7 ok!
[ 2.324] Log Block Index 0x00000003, LogicBlockNum: 0x000000c8, LogBlockType: 0x00000001
[ 2.327] log0: 0x00000785, Log1: 0x000007f7, WriteIndex: 0x00000000
[ 2.333] datablock: 0x000005e2, lastusedpage: 0x000000fb
[ 2.339] _RepairLogBlkTbl end
[ 2.350] The 0 disk name = bootloader, class name = DISK, disk size = 0x426ffe9c
[ 2.352] The 1 disk name = env, class name = DISK, disk size = 0x426ffe9c
[ 2.359] The 2 disk name = boot, class name = DISK, disk size = 0x426ffe9c
[ 2.366] The 3 disk name = system, class name = DISK, disk size = 0x426ffe9c
[ 2.374] The 4 disk name = data, class name = DISK, disk size = 0x426ffe9c
[ 2.381] The 5 disk name = misc, class name = DISK, disk size = 0x426ffe9c
[ 2.388] The 6 disk name = recovery, class name = DISK, disk size = 0x426ffe9c
[ 2.396] The 7 disk name = cache, class name = DISK, disk size = 0x426ffe9c
[ 2.403] The 8 disk name = private, class name = DISK, disk size = 0x426ffe9c
[ 2.410] The 9 disk name = sysrecovery, class name = DISK, disk size = 0x426ffe9c
[ 2.418] The 10 disk name = UDISK, class name = DISK, disk size = 0x426ffe9c
[ 2.426] Part 0: part_type: 0x0x00000000
[ 2.430] startblock: 0x0x00000008, endblock 0x0x00000010
[ 2.436] Part 1: part_type: 0x0x00000000
[ 2.440] startblock: 0x0x00000010, endblock 0x0x00000018
[ 2.446] Part 2: part_type: 0x0x00000000
[ 2.450] startblock: 0x0x00000018, endblock 0x0x00000028
[ 2.456] Part 3: part_type: 0x0x00000001
[ 2.460] startblock: 0x0x00000028, endblock 0x0x000000c8
[ 2.466] Part 4: part_type: 0x0x00000001
[ 2.470] startblock: 0x0x000000c8, endblock 0x0x000001c8
[ 2.476] Part 5: part_type: 0x0x00000000
[ 2.480] startblock: 0x0x000001c8, endblock 0x0x000001d0
[ 2.486] Part 6: part_type: 0x0x00000000
[ 2.491] startblock: 0x0x000001d0, endblock 0x0x000001e0
[ 2.496] Part 7: part_type: 0x0x00000001
[ 2.501] startblock: 0x0x000001e0, endblock 0x0x00000220
[ 2.507] Part 8: part_type: 0x0x00000000
[ 2.511] startblock: 0x0x00000220, endblock 0x0x00000228
[ 2.517] Part 9: part_type: 0x0x00000000
[ 2.521] startblock: 0x0x00000228, endblock 0x0x000002c8
[ 2.527] Part 10: part_type: 0x0x00000000
[ 2.531] startblock: 0x0x000002c8, endblock 0x0x00000760
[ 2.537] NB1 : init ok
[ 2.540] flash init finish
[ 2.543] fs init ok
[ 2.546] fattype FAT16
[ 2.548] fs mount ok
[ 2.550] script finish
[ 2.553] boot power:unable to find dcdc4 set
[ 2.558] power finish
[ 2.574] BootMain start
[ 2.574] 0
[ 2.585] key value = 0
[ 2.585] recovery key high 6, low 4
[ 2.586] unable to find fastboot_key key_max value
[ 2.592] test for multi os boot with display
[ 2.596] show pic finish
[ 2.598] load kernel start
[ 2.620] load kernel successed
[ 2.620] start address = 0x4a000000
U-Boot 2011.09-rc1 (Nov 29 2012 - 20:36:02) Allwinner Technology
CPU: SUNXI Family
Board: A10-EVB
DRAM: 512 MiB
NAND: 3776 MiB
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:11-
-name- -start- -size-
bootloader : 1000000 1000000
env : 2000000 1000000
boot : 3000000 2000000
system : 5000000 14000000
data : 19000000 20000000
misc : 39000000 1000000
recovery : 3a000000 2000000
cache : 3c000000 8000000
private : 44000000 1000000
sysrecovery : 45000000 14000000
UDISK : 59000000 93000000
-----------------------------------
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x3000000, size 0x2000000
33554432 bytes read: OK
Starting kernel ...
[ 0.187728] cryptomgr_test used greatest stack depth: 6672 bytes left
[ 0.188142] cryptomgr_test used greatest stack depth: 6480 bytes left
[ 0.190336] cryptomgr_test used greatest stack depth: 6120 bytes left
[ 0.218189] sw_ahci sw_ahci.0: AHCI is disable
[ 0.222748] sw_ahci: probe of sw_ahci.0 failed with error -22
[ 0.521586] [LCD] lcd_module_init
[ 0.588835] regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
[ 0.596873] regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
[ 0.604897] regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
[ 0.612833] regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
[ 0.620756] regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
[ 0.628659] regulator_init_complete: axp20_ldo1: incomplete constraints, leaving on
[ 0.639321] init: could not import file init.sun4i.usb.rc
[ 0.696874] init: to sleep 1 seconds.
[ 1.700802] init: has waken up.
[ 1.703984] init: [william] hdmistatus = 0!
[ 1.708171] init: [william] tvstatus = 0!
[ 1.712590] init: width = 1280
[ 1.715658] init: height = 720
[ 1.718723] init: s.st_size = 3686400
[ 2.043504] EXT4-fs (nandd): VFS: Can't find ext4 filesystem
[ 2.061565] init: do_umount: /data
[ 2.198835] init: do_umount: /cache
[ 2.212841] init: dont need format /dev/block/nandk
[ 2.218923] init: dont need format /dev/block/nandi
[ 2.229917] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 2.240448] init: cannot find '/system/bin/sh', disabling 'console'
[ 2.246726] init: cannot find '/system/bin/servicemanager', disabling 'servicemanager'
[ 2.254700] init: cannot find '/system/bin/vold', disabling 'vold'
[ 2.260944] init: cannot find '/system/bin/netd', disabling 'netd'
[ 2.267136] init: cannot find '/system/bin/debuggerd', disabling 'debuggerd'
[ 2.274223] init: cannot find '/system/bin/surfaceflinger', disabling 'surfaceflinger'
[ 2.282183] init: cannot find '/system/bin/app_process', disabling 'zygote'
[ 2.289162] init: cannot find '/system/bin/drmserver', disabling 'drm'
[ 2.295728] init: cannot find '/system/bin/mediaserver', disabling 'media'
[ 2.302645] init: cannot find '/system/bin/sambaserver', disabling 'netshare'
[ 2.309786] init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
[ 2.316633] init: cannot find '/system/bin/installd', disabling 'installd'
[ 2.323552] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 2.331946] init: cannot find '/system/bin/keystore', disabling 'keystore'
[ 2.338838] init: cannot find '/system/bin/u3gmonitor', disabling 'u3gmonitor'
[ 2.346106] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 2.352850] init: cannot find '/system/bin/securefileserver', disabling 'securefile'
[ 2.360629] init: cannot find '/system/bin/isomountmanagerservice', disabling 'isomountmanager'
[ 2.480392] init: cannot find '/system/bin/sh', disabling 'console'
The boot sequence on this device is slightly different in that the A10's boot loader jumps to uboot and then uboot boots to the kernel, rather than A10 straight to kernel. Apart from some version number differences the A10 boot loader appears to be the same as before - at least it appears to have all the same modes (FEL, key test etc).
The kernel output at the end of the boot indicates that some sort of file system corruption has taken place, which right now I'm attributing to over heating. The A10 feels hotter than I would like and there is very limited air flow through the casing, so I'm planning on installing a heatsink and to maybe modify the case.
The device is a JUSTOP Android 4.0 TV Box. Below are images of the front and back of the board.

Click here for a higher resolution PNG. Interesting you can see a space for a microphone at the front of the board (bottom of the image). The tracks appear to be connected to the A10.

Click here for a higher resolution PNG. On the right side of the image you can see the IC and the module that make up the wifi hardware.
In the end I recovered it by flashing with the latest stable firmware as per the manufacturers instructions.